Golf V 的恆溫空調顯示面板非但只有顯示溫度而已，還可以顯示許多有用的參數，用來監控引擎等運作狀況。
如何操作:
同時按下" econ"及 循環按鍵右方的" 箭頭往上 " 的按鈕，就可以進入到監控模式。
左方的顯示幕會出現"-"，"大數字"及"小數字"。減號不用理會。大數字代表main channel。 小數字代表sub channel。而右方顯示幕則顯示各參數的值。
( 各參數意義請對照download的參數表) 面板上左邊調溫度的旋扭用來調整main channel。中間風量調整旋扭用來調整sub channel。要回到正常模式按一下econ鍵就好了。
進入方法:
開啟空調後，按住<室內循環>鍵不放，再按住右上方<↑>鍵， 然後放開，此時，溫度顯示面板就會顯示功能代號 ( 1C ~ 61C )， 按 <+> 或 <-> 鍵來選擇功能代號， 選定後， 按 <室內循環>鍵，就可以顯示代表值了。 再按一次<室內循環>鍵， 就退回功能代號選擇。
例如，選擇 17C 之後， 再按 <室內循環>鍵，就會顯示目前的行進速度， 這個比儀表板的準 ( 實際從輪胎轉速計算出 )玩玩看吧。
Accessing On-Board Diagnostic codes
Press and hold the recirculation button. Then press the manual flow control up arrow. You should see a 1c. Press the temperature up ("+") or down ("-") buttons to select a code number. Then press the recirculation button again. The value should display. Press the temperature up or down button again to display another code.
NOTE: Air Flow Motor (V 71) and Potentiometer (G 113) are not installed in USA/Canada vehicles. Disregard values displayed for these components.
Code Displayed Value
1C System malfunction - displayed as a Diagnostic Trouble Code (DTC), see chart below
2C Digital value of Interior Temperature Sensor, in Headliner (G 86)
3C Digital value of Interior Temperature Sensor, in Instrument Panel (G 56)
4C Digital value of Fresh Air Intake Duct Temperature Sensor (G 89)
5C Digital value of Outside Air (Ambient) Temperature Sensor (G 17), front
6C Digital value of Outside Air (Ambient) Temperature Sensor
7C Digital value of Ambient Temperature Sensor At Fresh Air Blower (G 109)
8C Digital value of Temperature Regulator Flap Motor Potentiometer (G 92)
9C Delta value of Temperature Regulator Flap
10C Non-corrected specified value of Temperature Regulator Flap
11C Digital value of Central Flap Motor Potentiometer (G 112)
12C Specified value of Central Flap
13C Digital value of Footwell/Defroster Flap Motor Potentiometer (G 114)
14C Specified value of Footwell/Defroster Flap
15C Digital value of Air Flow Flap Motor Potentiometer (G 113)
16C Specified value of Air Flow Flap
17C Vehicle Speed (km/h)
18C Actual Air Blower voltage (Volts)
19C Specified Fresh Air Blower voltage (Volts)
20C A/C Compressor (A/C Clutch) voltage (Volts)
21C Number of low voltage occurrences, non-transient
22C Cycle condition of A/C Refrigerant High Pressure Switch (F 118)
23C Cyclings of the A/C Refrigerant High Pressure Switch (F 118)
24C Cyclings of the switches, absolute non-fluctuating
25C Analog/Digital value, Kick-Down Switch
26C Analog/Digital value, Engine Coolant Temperature (ECT) Warning Light
27C Coding value
&
如何操作:
同時按下" econ"及 循環按鍵右方的" 箭頭往上 " 的按鈕，就可以進入到監控模式。
左方的顯示幕會出現"-"，"大數字"及"小數字"。減號不用理會。大數字代表main channel。 小數字代表sub channel。而右方顯示幕則顯示各參數的值。
( 各參數意義請對照download的參數表) 面板上左邊調溫度的旋扭用來調整main channel。中間風量調整旋扭用來調整sub channel。要回到正常模式按一下econ鍵就好了。
進入方法:
開啟空調後，按住<室內循環>鍵不放，再按住右上方<↑>鍵， 然後放開，此時，溫度顯示面板就會顯示功能代號 ( 1C ~ 61C )， 按 <+> 或 <-> 鍵來選擇功能代號， 選定後， 按 <室內循環>鍵，就可以顯示代表值了。 再按一次<室內循環>鍵， 就退回功能代號選擇。
例如，選擇 17C 之後， 再按 <室內循環>鍵，就會顯示目前的行進速度， 這個比儀表板的準 ( 實際從輪胎轉速計算出 )玩玩看吧。
Accessing On-Board Diagnostic codes
Press and hold the recirculation button. Then press the manual flow control up arrow. You should see a 1c. Press the temperature up ("+") or down ("-") buttons to select a code number. Then press the recirculation button again. The value should display. Press the temperature up or down button again to display another code.
NOTE: Air Flow Motor (V 71) and Potentiometer (G 113) are not installed in USA/Canada vehicles. Disregard values displayed for these components.
Code Displayed Value
1C System malfunction - displayed as a Diagnostic Trouble Code (DTC), see chart below
2C Digital value of Interior Temperature Sensor, in Headliner (G 86)
3C Digital value of Interior Temperature Sensor, in Instrument Panel (G 56)
4C Digital value of Fresh Air Intake Duct Temperature Sensor (G 89)
5C Digital value of Outside Air (Ambient) Temperature Sensor (G 17), front
6C Digital value of Outside Air (Ambient) Temperature Sensor
7C Digital value of Ambient Temperature Sensor At Fresh Air Blower (G 109)
8C Digital value of Temperature Regulator Flap Motor Potentiometer (G 92)
9C Delta value of Temperature Regulator Flap
10C Non-corrected specified value of Temperature Regulator Flap
11C Digital value of Central Flap Motor Potentiometer (G 112)
12C Specified value of Central Flap
13C Digital value of Footwell/Defroster Flap Motor Potentiometer (G 114)
14C Specified value of Footwell/Defroster Flap
15C Digital value of Air Flow Flap Motor Potentiometer (G 113)
16C Specified value of Air Flow Flap
17C Vehicle Speed (km/h)
18C Actual Air Blower voltage (Volts)
19C Specified Fresh Air Blower voltage (Volts)
20C A/C Compressor (A/C Clutch) voltage (Volts)
21C Number of low voltage occurrences, non-transient
22C Cycle condition of A/C Refrigerant High Pressure Switch (F 118)
23C Cyclings of the A/C Refrigerant High Pressure Switch (F 118)
24C Cyclings of the switches, absolute non-fluctuating
25C Analog/Digital value, Kick-Down Switch
26C Analog/Digital value, Engine Coolant Temperature (ECT) Warning Light
27C Coding value
&
全站熱搜
留言列表
